Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I am trying to send GPS coordinates over HTTP, but get some problems when is comes to the use of lte_lc functions: lte_lc_init(), lte_lc_psm_reg(true), lte_lc_connect...
I am using the DK PCA10041 with SDK 17 and mesh SDK 5.0.0. I have run into an odd issue. I set up the dimming mesh example with a client and two servers and provisioned them...
Hello,
I have created a standalone application using the NCS nrf SDK and Zephyr. I do manage all my project dependencies using West. I have some questions related to the...
I referred to the following sample.
\ncs\v1.4.2\zephyr\samples\subsys\nvs\src\main.c
void main(void) { int rc = 0, cnt = 0, cnt_his = 0; char buf[16]; uint8_t key[8],...
good day, we plan to create a device which will send button status and the ble_blinky example seems to match our requirement. is it possible to add pairing/repairing option...
Hi
I have managed to get a SNTP client working. I want to update the date-time clock with the SNTP timestamp. From the SNTP client I get a sntp_time object:
While the...
Hi,
We are looking to purchase the nRF52833 DK. The data sheet says it supports an RX sensitivity of -95dBm. Does it not support up to -103dBm as quoted on the data sheet...
Hey,
I would like to know if its somehow possible to rebond if the central device (nrf52) has deleted the bonding information about a device and then this deleted peripheral...
I'm trying to implement a timer with 1ms resolution that my application can use externally using a callback function.
The idea is to
Implement the timer as a 32-bit...
Hi all,
I need to upgrade an nRF52 device with SoftDevice 5.0.0 and bootloader.
I have to upgrade from SD 5.0.0 to 7.2.0.
I use this command to generate the zip file...
Dear all,
I have some problem with SPIs co-work.
I enabled two SPI instances in this project.
SPI Instance 1 function(non blocking mode - DMA enabled, 4Mbps): reading...
Hi there, Thanks in advance for your time and attention. We started to see some cases where our devices boots and gets a NO_PAGES error after having been turned off(or at...
I try to simulate system hang by adding while(1) after calling watch dog feeding function. But watchdog event handler _wdtEventHandler() isn't called.
int main(void) { ...
Hi,
I am currently trying to read the GPIO latch register in my Zephyr NRF SDK 1.9.1 C++ project with the following line:
This is resulting in the following compile...
