Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Been chasing this undefined reference to `__device_dts_ord_XXX' issue around for awhile now with no clear path forward. What I am observing is extremely similar to...
Hello,
I am working on Thread client server based network. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development hardware is nRF52840-DK, HW Version 2...
Hi,
I am using nrf toolchain v2.0.0, and am testing the dfu-ota example over BLE by following the below link ( ) . howveer for fast boot up, i am using "
CONFIG_BOOT_VALIDATE_SLOT0_ONCE...
It is possible to change the partition table through a FOTA?
Is the partition table stored somewhere on the device, or is it merely used for linkage? If it is linkage only...
Does anyone know how to use the CMSIS-DSP FFT library on a nrf52832?
I am using the nrf Connect SDK and it seems all of the examples are for nrf5 SDK.
I am looking to...
i use the ubuntu20.04 and open nrfconnect-3.11.1-x86_64.appimage through proxy successfully
then i install and open the toochain manager , there is not include NCS 2.0...
We are developing a new product and plan to use nRF52810. As I understand nRF52 will be supported for production in the new nRF Connect Release (1.3.0) that will come soon...
Hello,
Our application requires the device to go into deep sleep and wake up every 24Hr or on the Accelerometer interrupt. We were able to obtain the sleep mode and wake...
I'm trying to migrate my project to NCS 2.0.0 but having an issue like below:
c:/ncs/toolchains/v2.0.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/10.3...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi We have designed some boards with ESPRESSIF WiFi BLE Module ESP-32-WROOM-32E for control and monitor.
Is it possible to connect esp32 to nRF21540 to extend range ( such...
Hi, I am using nRF52840 and communicating with Simcom GSM( Sim7600g ). 1- Is there any example code/ Library to connect with the MQTT server?
2- Can I use this example code...
I found my thread device to have quite a large latency so I analysed the communication and found out that the device is actually timeouting and retrying before listening for...
We are trying to connect MQTT over IPv6 with nrf9160dk and custom board. We are using mqtt_simple sample.
Software NCS version: NCS main (latest)
Changes in the code:...
