I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
Hi,
I would like to read the temperature of the nRF.
I tried to use the routine I found here in the forum
Sometimes works sometimes the system crash. I notice the...
Hi
I am using NRF5340 chip in my custom board to communicate serially with an external device whose data length is more than 128 bytes.
The chip can receive 243 bytes...
I am looking for the examples for the SDK. I installed SDK 1.9.1 through the Toolchain Manager and see the directory "users/my_user_name/ncs/v1.9.1" Supposedly this is where...
Hi,
In Openthread's Coap_client sample, Following 2 libraries are there:
and while compiling my code I get multiple warning regarding to above 2 libraries.
Following...
Hi,
I have problem to use bmi160 library with nrf5340 in spi connection.
I use the example application zephyr/samples/sensor/adxl372 and change the sensor to bmi160 (...
Hi DevZone ! Here is my issue: I use to work with VSCode and nRF Connect for desktop for a few months now. Early on Monday, I did uninstall all my dev environment (VSCode...
Hi,
is there any way to get a Pin to a defined "high" without vdd-gpio ref?
In our situation the NRF9160 Power is a Battery with 4,1V and the VDD-GPIO is 3,3V with a regulator...
I created two build configurations a Debug and a Release in SES IDE.
Build > Build Configurations...
I wanted to select the DEBUG_OPTIMIZATIONS level for the Debug build...
This is a continuation of the topic here that is now closed
https://devzone.nordicsemi.com/f/nordic-q-a/85590/nrf9160-azure_iot_hub-change-dps-username-during-run-time ...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
