Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
Device: NRF53
I'm trying to send 3 notify packets in a 15ms connection internal but I can send 2.
I'm using Nrf connect and Zephyr. is there a limit or a define...
I seem to be having weird issue upon initializing qwr module in my .cpp file
NRF_BLE_QWR_DEF(qwr);
Doing so results in a syntax error
#define NRF_BLE_QWR_DEF(_name...
I created a custom BLE service following this tutorial and I am able to connect to the BLE service and write data to it, but ideally, I want to send character bytes as opposed...
Hello,
we are using an nRF52833 for our application with the open serial uart bootloader and MBR programmed in it. What we would like to do is:
1) program the application...
Hi everyone, I'm trying to get the LIS2DH12 driver (SDK v15.0.0) to configure a LIS2DH12 sensor connected to my nRF52 Dev Kit. I've wired the chip up as follows (using the...
I set the publish address of client using function:
Unicast address of sever is 0x0003.
After setting publish address by this function, I check publish address from...
Hello community... I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful. However, checking...
NRF52833+SDK17:
I want to use the saadc to sample a DC brushed motor running current when pwm at rising edge, pwm driving the motor.
I can't understand the real meaning...
Hi, I've been working on SDK v1.6.1 and I just wanted to try the v1.7.0, however some functions on the power management have changed, in particularly:
int pm_device_state_set...
I am encountering a problem with programming an nRF52840 DK:
1. I've installed nRF Connect for Desktop version 3.7.1, nrfjprog version 10.14 and Segger JLinkARM.dll version...
Hi,
I'm using the CLI and have logging enabled. The only way I'm able to see my logging output is if I type "log enable info" at the CLI prompt.
Is there a way to enable...
Hi to every one,
i have some questions, I need to be able to update the device to the new firmware, update to the old version and update to the default firmware. for this...
I am connecting the nRF52 DK to an oscilloscope and on the LED pin for the dimming example on the server side. I am seeing jitter, the PWM duty cycle doing a slight shift...
