I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am completly new in nrf52, nrf-connect and zephyr environment.
I need to configure pwm channels that wont be used to drive led...
Most of thing is undestand for...
Sending a PSK like:
AT%CMNG=0,42,3,"1r0nm@n"
should result in failure, as that is not a valid hex string (as documented in nRF91 AT Commands). Currently this results in...
Hello,
I am trying to run the CCS881 sensor sample in my nrf9160 board. I have made changes to my project config file and main.c file as mentioned in
https://devzone...
I need to compare two ble_date_time_t structs to figure out if one is later than the other. So basically I need to check if rtc_datetime > expiration_datetime. Both rtc_datetime...
I plan on writing my own service (similar to NUS) but prior to that, I'd want to use all the existing APIs for initializing the GATT and BLE stack at least
I'm calling the...
Hi Team,
i have trying to create multiple serial port with debug log enabled in the sdk code sample but when i am going to init log_init a long with any UART / SERIAL...
HI
I still try to reconfigure my Zaphyr testing environment to NRF Unity/CMock but I've encountered more issues.
1. __syscall mocking
Is there any reason to exclude...
Hello there,
I'm trying to interface msp430 (master) with nrf51882 (slave) through SPI. I'm running soft device 110 to broadcast the received data from SPI through BLE...
Is there comprehensive documentation on DFU, mcuboot, and zephyr somewhere? I have an nrf52840-based device running a Zephyr 2.4-based application with mcuboot 1.7 as a bootloader...
Hi, I am trying to interface Max31865 with NRF52832 via SPI communication. My module RTD pt100 working fine with Arduino but I am getting unchanged wrong value while programming...
Hi there,
I have used the nrf2724 (radio module) as a prototyping platform. I am able to flash my personal program to the nrf24le1 on the nrf2724 and it functions properly...
Hello!
I'd like to briefly introduce what I'm attempting to do: I'm trying to flash some samples from the Zephyr project into a custom board. The custom board is based on...
Hi,
I tried to update DFU keys via update on SDK-4.1 and I didin't to do it. Its possible to change DFU keys via upgrade. I did this process on SDK-2 and there was no validation...
We are looking to get started evaluating the nRF5340 with the DK on Windows 10, but our User directories all have spaces in them (they default to our names and are not changeable...
Hi
I want to use nrfutil as a command line tool on a Raspberry Pi 4 box.
Out of the box, I could not install nrfutil (missing drivers?) compatible with Python3 so I tried...
