I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi.
I recently started work on some projects where I have to use I2c OLED and BLE. I used OLED to display time which is running on an internal RTC of nrf52832.
Now I merge...
Hello sir,
i am using nrf52832 board and i am getting following error when i build the code are as follows:
1..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
Hello,
I am trying to change the device name in the ble advertisement in the secure_bootloader example.
Module model: nrf52832
Sdk: 15.2
I have tried to put...
Hello Nordic support,
I am working on a Zigbee coordinator application to make it work with an IAS zone Zigbee device.
As per the Zigbee device specification, ''when it...
Hi , I want to send a char data through bleutouth using ble nus I am using this method
I don't have any error but I don't receive any information on my android application...
I am using nRF Connect for Android and had a question about a script I would like to develop: for this script, I would like user input to specify part of the value I write...
On the nRF 52840, is there a way to have the TWIM peripheral suspend a transfer after transmission of a single byte? The TWI peripheral provides the BB_SUSPEND short, but...
Hi engineer,
i am running a example:SDK 12.2/ANT/ant_bpwr,MCU:NRF52832;i want to dynamically modify the value of "CHAN_ID_DEV_NUM" by reading the UICR value for distinguishing...
I am trying to figure out how to use the SAADC component of the nRF52840 to measure an analogue input and report it as an attribute in a Zigbee end device. I have, so far...
Hello,
I am analyzing the DKs power amplifier characteristics as an assignment for university. I got the serial_lte_modem running and send AT commands via UART from an external...
Hi,
I am looking for a 4G module with in built gps in it. It has to work in european market, need to have esim facility.
Can you provide with the product links.
-
...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
