I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear,nordic:
Please help me allocate more than 80KB of memory on this routine.
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2.0\nrf\applications...
Hi Team,
We are using Nordic nRF52840 in one of our projects, we want to check RF performance, so we want to use our IC is in DTM mode or continuous communication mode,...
Importing the IAR peripheral beaco example file for S132 into Segger seems to work with the one exception of app_error_handler_iar.c where the assembler reports an error as...
Hello everyone,
I have done researches on the forum but I did'nt find any answer. I would like to programm the dongle througth the SWDio and SWDCLK of the Dk.
1) is it...
Hi, I'm designing water meter modem using the nRF52840 + nRF9160. I will apply nRF52840 as a HOST CPU and the nRF160 contol by nRF52840. (please refer to attached picture...
Hello,
I am interfacing a NRF52832 with a PCF8574 I2C slave using SDK 15.0.0.
As per the datasheet, the device will send the data to the slave after it receives the write...
Dear Sir,
I designed a new pcb based on nrf9160,
The boards are populated with cipsim.
When running the MQTT_SIMPLE project i get the following error for the 2 boards...
Hi,
We are upgrading our product from SDK 15.0 to SDK 17.0.
In the old SDK there seems to be one file abailable: ../SDK_15/External/nrf_cc310/lib/libnrf_cc310_0.9.9.a...
Hello:
We are developing a DFU bootloader for an NRF52 product that supports USB and BLE upload methods (they are 2 separate bootloaders from a common source). Both work...
I am hoping to pass data from the nRF52840 to the nRF9160 over UART_0, on a custom PCB. For context, the aim is to pass data at a rather quick rate and good reliability. The...
HI,
I want to make a receiver to get BLE packets on any channel.(NO SOFTDEVICE)
I fail to fullfile it yet by reading <nRF52810_PS_V1.3.pdf>.
Any other hands can give...
Hi,
I am working on the asset_tracker application example on a Thingy:91 device. As I understand it, to activate the GPS it is necessary to keep the button pressed for a...
Hi,
In nrf9160 I want to check the communication of LTE device.
I have installed nRF Connect for Desktop, Getting Started Assistant, LTE Link Monitor, & Programmer.
...
