Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi everyone,
I'm trying to developp a MIDI USB class compliant device with the nrf52840 DK.
I'm beginner about USB developpement and I have only basics about MIDI class...
I am using SDK 15.3.0 working on nRF52832, on windows platform.
Our requirement is, we need to get the data from both nRF52832 and BLE Heart rate sensor at same time and...
I have developed a new board based around NRF91 module. Ten prototypes are produced and six of them work. Other four devices cannot connect to the LTE network. I am using...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
Hello
the setup is a nrf52840, the sdk15.3, Softdevice s140, apps: open bootloader and blinky app
Is there a way that the DFU mode is always there, at the moment its only...
Hi,
We are in the HW verification stage of a product with an nRF52 series MCU. We were easily able to measure the 32MHz XTAL accuracy using the buffered output feature;...
Hello, Dear Support!
From the DevZone I downloaded ntf5-multilink-example-master. Here . Thanks for developers. The solution in SES was built and uploaded without any troubles...
I am using 'Segger Embedded Studio'. While changing the settings of a project in options, why we select Private Configurations (common)? I have seen this procedure in many...
Hi,I had a new project base on nRF52810. I watnted to created a timer, but the note mentioned " increase the value of the macro APP_TIMER_MAX_TIMERS by one ".I couldn't find...
Hi,
is nRF9160 SiP comes with eSIM? or do I need to insert external SIM in socket which is traditional method?
Do I need to external chip antenna? does that antenna...
Hi:
Because our project using much nRF pin resources, we have to use the defualt function NFC pins (P0.09 and P0.10).we want to set these two pins as uart function ,but...
Hi everyone,
I m nRF52 beginner and trying to understand that functions.
I have the few of qustions about DFU.
1. Is it that the mean of DFU equels "OTA DFU" referred...
I'm looking for a way to reliably determine (from the applications viewpoint) if a notification was successfully transmitted. Currently, we're having some issues when the...
Hello,
I am new to nrF52 480 chip. I am working on SDK15.3.0_59ac345's beacon code but have no result in the attempt to add device name to the existing beacon example. ...
Hey guys. I was working on a PCA10059 dongle. Now, I need to select suitable NRF52840 module. I know that there are some changes required in the code when I use module like...
