Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
nRF52832 power consumption is high after the SPI peripheral is used (approximately 400uA of extra current consumption). I expect it has something to do with the high speed...
Hi,
I am using the nrf52832 board for my project.
I am using the NUS example as a base for my project.
2 services are provided by this application i.e RX Characteristic...
I'm trying to flash a Nordic Thingy. I have it connected to the debug port of a nRF52840-DK, nrfjprog --ids lists no boards, however.
However pyocd produces:
...
I have a question about bonding with "Peer Manager".
I am using the sample project "ble_app_multirole_lesc (SDK V15.3.0)".
I am bonding by "Peer Manager". When bonding...
Why does SPI not work with nrf_delay, from this previous question
devzone.nordicsemi.com/.../
Surely the SPI SCK is a PWM or other timer/interrupt driven clock?
Also...
When i use nrfutil to perform DFU it is passed, but when i send it through STM32 dev kit it Hash validation failed. but however i can see the CRC is correct.
Hello,
I have an AMS AS7261 light sensor that I'm using with my NRF51422 DK to take a light reading, pull it using nrf_drv_twi_tx/rx, and send it over BLE. However, when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few variables in application. These will...
i have a complete project based the gfx project and i want to add BLE using UART for communication. i want to communicate my module with the nRF52840 dongle.
is there simple...
SDK14+NRF52832.
I used one timer to do something every millisecond. and I used another function to do a loop action, the function maybe breaked if the time period exceed...
Can not connect Android 8 mobile phones, such as HUAWEI Nova 3
Nodic equipment is not even found.
We cannot connect with official UART routines.（ble_app_uart...
I found a terminal that can not communicate with BLE. I think that the sequence after MTU exchange is strange. The program used is sample HRM. The terminal used is "Xperia...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello, I am using the nRF52840 dev kit. I am using SES to develop the code for it. I want to include the bosch bme680 library in my code. It comes as a libalgobsec.a file...
