Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everyone,
We are currently working on a BLE border router with a module based on nrf52840. The custom board has a MAC + PHY ethernet controller that communicates with...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have gone through below...
Hi everyone,
I completed tutorials and i tried to get a value from characteristic and i tried to do something extra. But i am encountering a problem which i could't understand...
hello.
My first nRF9160DK is 0.8.2 2018.49 and all demos goes well on it.
My second nRF9160DK is 0.8.3 2019.1 but none demos goes well on it except at_client.
Is there...
Dear all,
I want to know the methods to analyze Bluetooth 5 protocol, such that these packets sniffer tools: BLE USB Dongle from TI or nRF52832 DK.
Which one is better...
android OS: 6.0.1
nRF Connect: 4.22.3
nRF5 SDK: 15.2.0
Hello
With the nRF Connect For Desktop and also with the app on iOS, it works perfectly to perform buttonless...
Hello,
I understand reading your documentation that the nrf5x series have support for RPL but i can't find the implementation in the SDK 15.3.0.
Is RPL implemented in...
I am working on a project to do serial uart dfu in nrf52810. For that purpose i will be writing c code equivalent to nrfutil. I was going through all documentation and tried...
Hi, guys. I'm using PCA10056 and SDK 15.3's BLE UART peripheral example.
I also have a Microsoft HoloLens (the first version which runs Windows 10 and the HoloLens shell...
Hello
I am working with LIS2Dh12 accelerometer sensor interfaced with SPI 2 of nrf52832. For its one of the axis we have configured the interrupt which is working fine individually...
hi,i am using nrf52 DK kit. i have interfaced it with bmd 101 ecg sensor. The sensor sends continuous data over UART. I am using SEGGER IDE. The code which i am using is ble_app_uart...
Hi there,
I'm confused with the meaning of the 'vloc' variable in the attribute meta data. In the example code ble_bps.c of "ble_app_bps_pca10040_s132" , in the function...
Hello,
We are experiencing an issue that some of the nRF52832 is not starting up automatically. But we attached it with JLINK debugger and didn't do anything, it can boot...
Dear Community,
I'm including a wireless bootloader to enable firmware updates in my application. My question is the following:
Before entering in DFU mode from my app...
