Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Description:
For my project I'm using 3 Nrf52840 DK, two of them as peripheral and the other as peripheral and central. I'm using also an iOS device as central. The two...
Hello,
I bought a Adafruit Feather M0 Bluefruit LE, the Bluefruit LE module is an nRF51822 chipset from Nordic. I connected the Adafruit board to an accelerometer. This...
Hello, i currently evalutate LTE-M for my company and i run into a lot of trouble for starting the test. But at least i have able to do the test
I have cut a lot of code...
Hi Nordic,
It reads in devzone.nordicsemi.com/.../38040
"According to Section 8.23 in the Product Specification a logical high is between 0.7*VDD and VDD and a logical...
Although BUTTONS_ACTIVE_STATE declared as 1, the hal_buttons_init(button_event_handler) yields an event when the input sees a high to low transition in stead of a low to high...
In testing the timers on the dongle, I have made a GPIO pin be controlled by the timer triggering.
So the following has a constant time between edges:
case NRF_TIMER_EVENT_COMPARE1...
I ran into the same problem as other user one year ago (I was using Arduino Studio nad Segger Studio before), now I switched to IAR (as recommended) and as the examples are...
Using SEGGER Embedded Studio for ARM v4.20a (64-bit).
I'd like to add a new source file to a nRF9160 sample project. The menu selection Project --> Add New File is grayed...
Hi,
I had a custom nRF52832 board. I did some modifications on it. But the same code doesn't run on modified one.
Just to check, Debugging on Segger the yellow arrow(i...
I've been following the guide linked here and got to the point where PCA10090 is flashed with Hello World project. However, when executing "west flash" command, an error appears...
Developing on a custom nRF52832 board, not the Nordic nRF52 dev board, but continue to use version 15.2 of the SDK. Building and download application, but get an abort before...
Hello. I am now implementing communication to multiple peripheral devices based on the multi-roll project “ble_app_multirole_lesc”. (image1)
Central link after setting memory...
Hello,
I am developing an app for Android using the Android-nRF-Mesh Library, available here: https://github.com/NordicSemiconductor/Android-nRF-Mesh-Library
According...
Hi everyone,
I use nrf52840 DK with Segger embedded studio. I have created a project where I read several sensors data and send these data to mobile through BLE UART.
...
