Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I would like to create a repo to house all our vendor-specific board support, applications, etc. outside the Nordic nrfConnect repositories as per the Zephyr workflow. However...
Hi, I am an internship student and so new at programming. I have a nRF51822 DK that includes;
2 x nRF51822 module
2 x BLE master dongle
J-Link Cortex emulator (Debugger...
Hello everyone,
We have an IoT device with the nRF52832 module installed. We are in pre-production and in the process of certification. Our laboratory (EMITECH) asks us...
Hello team, i use board nrf52832 and SDK15.3. in example ble_app_uart_c. BLE_NUS_C_EVT_DISCOVERY_COMPLETE event occurs only once, after losing the connection and reconnecting...
Is there an example for setting up a Segger Embedded Studio project for using an nRF52840 with Zephyr. The instructions on the Zephry site for adding Zephyr files to a project...
Hello,
We are currently designing a device that will use the GPS on the nRF9160, our implimentation will involve using sensors to trigger GPS measurements for the duration...
I am using an nRF52832 and the Nordic UART Service (NUS). I am using the example NUS code and the UART side is plugged into another microcontroller's UART. By default that...
I need to find rssi value of my mobile (using nrf blink app) using nrf52840 Dk.. So i generally don't have idea what changes to be made for ble_peripheral->ble_app_blinky...
Looking at different solutions to an asset tracking system I'll be working on as my senior project later this year (getting a head start so time isn't as much of an issue...
Hi,
I'm writing a driver for a Ublox cellular module, which will be communicating with the nRF5240 using UART. After going back and forth, I decided to go with the app_uart...
Hello, I am an intern at a startup company and ive been tasked with finding some information about the chip set we are using, specifically the bluetooth aspects. We are using...
Hello,
I just installed SEGGER Embedded Studio to build the light switch example for Bluetooth mesh.
I managed to successfully follow the quick start guide using 3 development...
Hello!
I managed to flash my Raytac dongle with debugging going using the SWD on a nrf52 DK. I am mainly working with SEGGER Embedded Studio and nRF Connect on Mac. However...
i m getting constant RSSI values 32 even if i move far or near
this is the same example code in ble_peripherals
I HAVE UPDATED MY CODE (i have printed the RSSI values...
I have an android smartphone of bluetooth version 4 and i am developing one application where i am using nRF52 (bluetooth version 5). Is it possible to write data from the...
