Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
I have to send 15 bytes on uart of nRF52832 (nordic micro is the receiver), but I have APP_UART_COMMUNICATION_ERROR. If I send 5 bytes everything works fine, if I...
I have a beacon from Wellcore, w912, with NRF51822QFAAH0. I use NRF Connect and I see the temp and accel sensors but I dont know how to enable them. Is there a manual you...
In section 23.1 "EasyDMA" of the Product specification, it is written that "the S0INCL field in PCNF0 determines if S0 is present in RAM at all if its length is zero." But...
Hi I am building a project, where I need to initialize the ADC using a timer. Whenever there is a timer interrupt "nrfx_saadc_sample" gets called and ADC starts sampling....
I want to find the mac address of the nRF52 DK and assign the instance ID of the eddystone format.
I am using the eddystone sample app from the SDK 152 and softdevice 6...
Hi,
I would like to build an application on Ubuntu PC, using github.com/.../nrf52-ble-image-transfer-demo The purpose is to do some analysis of the images taken by Arducam...
Hey everyone, I'm having an issue communicating with a QSPI flash on a custom development board, using the nRF52840. The flash is a Winbond W25Q16JVSSIQ. Schematic and pins...
Hi,
I am using a custom NRF52832 board. I am using Nordic SDK + BLE code, and whenever I am trying to do an erase of flash memory with start address as 0x70000 and end address...
I try to get the info listed in the following paragraph (From the nRF91_DK user guide) but just get run the run around with the web site. Anyone got a link to this information...
The flash requirements for both the S132 v5.0.0 and v5.1.0 are the same, however the size of the v5.1.0 softdevice is quite a bit smaller.
S132 v5.0.0 uses flash addresses...
Hello I try to get the mac address of connected device
/**@brief Function for the application's SoftDevice event handler.
*
* @param[in] p_ble_evt SoftDevice event...
Issue with Zephyr software platform and sleep state for the Nordic chipset. We can see when using the power management sample code for Zephyr that it consume 300 uA in sleep...
hi,...... i am merging the nRF52832 and heart rate sensor BH1790, SEGGER 15.2V i want to read the heart rate sensor , for that i want to write the paramater of address, 41h...
After beating my head against the toolchain for quite a while, I finally managed to get SES to compile the ble_app_uart for the nRF51822 using the s130 soft device. It works...
