Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi
So far I have been using the examples from Keil 5 pack installer.
Now I tried loading some from the SDK example folder and I have issues with includes.
What do I need...
I included button less DFU service in the proximity profile example.When i compile i am getting the following error.
..\..\..\..\..\..\components\libraries\bootloader\dfu...
Hello,
I am working with the example "experimental ble app cgms" in SDK 13.0 and using nRF52832 DK.
when a connection was settup and pairing completed, the CGMS sensor...
I want to ask general question about antenna designing as I am designing antenna to be used with NRF52.
The picture attached with this message shows a printed antenna coil...
At the moment I'm sending a notificaties during the BLE_GAP_EVT_CONNECTED event. This sometimes results in various errors but I can take care of those. The issue I'm having...
GerberVINR-178.zip
SchematicVINR-178.pdf
Bottom layer
Top Layer
IC on the PCB is marked as follows: nrf51822 QFAAHO 1627WM.
I am able to program the custom...
Hello,
I want to create BLE connection between two different modules - nrf51822 and TI CC2564 (possibly Laird BT800). Is there any chance on using Gazell protocol on other...
Hi,
if I got it right, the Radio Timeslot API is not supported by the S140 softdevice. Is this right? Why is this and are there any plans to support the API in later versions...
HI, every one, I joined the watchdog program in application,i use sdk11.0, and i found the problem that when i download the program , the MDK compiler point out "error: flash...
Hi,
I am doing development on Android platform. I am using Marshmallow device to develop my BLE application. Many times I am getting status code 129 in onServicesDiscovered...
Hi, i'm working on a custom board with microswitch (Crouzet V4) in order to get the position of a moving part inside a machine. This switch is in pullup mode with a 100k resistor...
Hello,
I am using nrf51 and sdk12.2. I want to print data to terminal using printf function. So I added app_uart_fifo.c also I included paths. I did not get any errors from...
I'm using NRF51422, s130, SDK v12.
And I'm working on a project that can connect concurrent peripheral and Central.
In this continuious connect and disconnect sequences...
Hello,
I am using the bootloader_secure-Example on a custom-board and I want to configure a LED as status-indication.
Since I am on a custom-board I disabled the functions...
