Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I own company that builds a PIC 8-bit devices, and can code at a low bit level in the PIC environment.
I picked up the NRF52 Dev board, and am trying to learn the...
My peripheral device connects with central one very rarely. I decided that I don't want peripheral to negotiate connection parameters with central, just use settings imposed...
I'm developing custom board of nrF51822 CEAA (256k, 16k)
I set my bootloader ROM, RAM just like below
as I understand,
Firmware size should not larger than...
hi,
i just ask about nrf52832.
im using it with keil compiler and trying to divide the memory section (it that will be update and not)
but i have hard time to do with keil...
I'd like to log some debug stuff to a mobile app over BLE, when in a connection, using the NRF_LOG library and the Nordic UART service. I have this working just fine without...
I'm trying to write to specific address on flash memory (data region) for debug purpose using
nrfjprog.exe --memwr 0x3B820 --val 0xAA000000 --verify
but when I read...
So I'm still trying to get my way around the DFU service implementation, and I'm currently having trouble with the first step, which is to enable the control point notification...
Hi.
This is a bit of a combo question:
I recently got the nRF52 10040 and I'm trying out the included examples on uVision5.
I only managed some examples to...
I am working on BLE Applications, I have tested with different devices like Nexus, Moto, Samsung, LG(ble V 4.0). I am getting the GATT Error 133 in Samsung Devices alone(Samsung...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hi,
I have an nRF52 chip that has likely exceeded the flash endurance limit.
I am observing that after an ERASEALL, not all bits are erased, but after retrying ERASEALL...
Hi, does somebody know why in Segger embedded studio program goes to ses_nrf51_startup.s line 35 ISR_HANDLER NMI_Handler and sits there. I'm trying ble_app_cscs_pca10028_s130...
