Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi team,
I am using ncsv2.8.0, on our custom designed nrf52832 board.
Here I am trying to integrate i2c driver code for bme688 along with bsec library in peripheral_uart...
Hello,
i'm developing a custom board with nRF5340 (WLCSP package) that is very constrained in terms of space for a Bluetooth application. I looked on DevZone and i found...
I first tried nrfjprog which didn't work, but I know that's being retired so that wasn't entirely surprising. After that I moved on to testing 'nrfutil', specifically the...
I am building a BLE audio product that is based on the nRF5340. The application is largely based on the nrf5340_audio ncs example application, but I am modifying the the application...
Hi,
I am testing an actinius_icarus board V2.
I read data from senso BM68X every 500 ms, and publish on mqtt broker every 1 seconds. they are 256 bytes every sending....
Hi,
I am using NRF Cloud + coap comms to send data. However I have encountered payload size limitations that are not configurable via KConfig: sdk-nrf/subsys/net/lib/nrf_cloud...
Unable to find enough information to convert the raw values obtained from Thingy53 for RGB components.
Referred to BH1749NUC datasheet, Thingy53 sample code
Hi,
I am writing a custom i2c driver for an evaluation, when I ran the same i was getting exception:
during troubleshooting i scraped the entire custom driver and...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I'm applying an application firmware update by calling fota_download_start_with_image_type with DFU_TARGET_IMAGE_TYPE_MCUBOOT...
The Radio Notification Callback functionality found here is exactly what I am looking for. However, when I try to include the associated header < bluetooth/radio_notification_cb...
Hello everyone,
for my project I had to develop a new driver for the Kinetic 2026 LED driver.
I have attached the driver to my project like this in the Device Tree like...
I have some nRF52840 USB Dongles that I would like to turn into a generic BT receiver for SBC's that does not already have BT/WiFi chipset onboard. I was hoping I could program...
My laptop does not detect my dongle after I program it through nrfConnect. I am thinking that maybe I have to reflash the pca 10059 firmware, but I do not have any nrf development...
Using nRF5340 hci code, I've been able to get a device that connects and authenticates with two central devices. However, after connecting with one central device, I no longer...
