Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi, I want to use an NRF52805 with a voltage to frequency detector. If I understand the datasheet, there is one timer/counter and RTC on that chip. Is it possible to set the...
Hello,
How do I deactivate/activate a SDA/SCL line?
I perform a test on an Icarus board with a VL53L1X sensor, everything works fine.
However, in idle/sleep mode, whether...
Hi,
I am unable to view the output of the prink statement on the SES debug terminal. I'm a beginner so please bear with my lack of knowledge.
Should I be looking for the...
I am trying to adapt the zigbee light_bulb sample to run on nrf52840-Dongle which does not have a QSPI flash chip. I see that it crashes unexpectedly during settings_subsys_init...
Hello,
We have product with nRF52811 as Bluetooth receiver and ESP32 as WiFi IC. The ICs have separate antennas, and nRF52811 has LNA with +12 dBm gain connected to antenna...
https://github.com/project-chip/connectedhomeip/blob/master/docs/guides/nrfconnect_examples_cli.md
uart:~$ clear date device devmem flash help history hwinfo kernel nrf_clock_control...
I have loaded up the altium design and can see the pad and via sizes used.
The drill size for the in pad via is very small (0.15mm) which will increase pcb costs and also...
*** Booting Zephyr OS build v2.7.99-ncs1 ***
nrf52840dk_nrf52840 system off demo Retained data not supported Busy-wait 2 s Busy-wait 2 s with UART off Sleep 2 s Sleep 2...
Hi,
Installed the toolchain, installed VS Code, and I think its all linked, but when I try to run even the most basic hello world program it just keeps throwing this error...
hi support team,
i am confused about "advertising extentions" part;
Inforcentor shows example for " Cycling Speed and Cadence Application" only support S132 and S140,...
Hi,
I am developing my own vendor specific USB device with 2 interfaces (data and debug) and 2 endpoints(in and out) each. I based my class on the cdc_acm class.
So far...
Hello ,
hi everyone, in my project i am using internal RTC timer for calendar concept like when i set a target time via UART for every day the internal RTC timer should...
So I have to upload a bunch of files, some contain arbitrary data that might contain +,\r,\n,\ ext
So there are two different ways of using the FTP put command, one is in...
I've tried to run a program which allows to run mesh provisioner, among with Direction Finding connectionless locator.
I was using mesh provisioner example from Zephyr,...
I am at the final stage in the current project but the send status is not updating correctly when
an attribute value is sent. For example in the following code:
zcl_status...
