Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Is there any guide or sample how to run unity tests on a target device instead of the native_posix device?
In general unity however cmock support on-device testing like...
Hello,
My config: - nRF SDK v17.1.0 - nRF SoftDevice S140 7.2.0 - FreeRTOS Kernel v10.0.0 (Amazon.com)
My project used BLE connection with custom service (based on NUS...
I want to use dynamic memory allocation. After searching these forums, I see the following options:
malloc
k_malloc
nrf_malloc
balloc
I haven't had success with...
Hello everyone I hope you all had a good start to the week. I am stuck with an issue I don't quite get. I wrote code with BLE, FreeRTOS, and GPIOTE as a "proof of concept...
Hi,
I'm evaluating the NCS peripheral_uart example for our needs.
I have an issue with deploying this example to an PCA10040 board. While running the example built for...
Hi All!
I have a problem which i can't really understood. I'm using nRF5340-DK evaluation board, and currently i'm trying to get one of timer (TIMER1 in this example)...
Hello,
I have a Nordic connected to a STM32. The DFU procedure on the Nordic works fine and I am able to upload and run a new firmware in buttonless mode. The Nordic also...
nPM1100 use JEITA profile that has charging range 0-60gc. Most batteries has charging range 0-45gc. Is it possible to limit charging to 0-45gc with this chip, or is JEITA...
Hi,
I am developing a product using the SoftDevcie s140 and SDK 17.0.2.
I have the problem, that the standard FreeRTOS port defines configTICK_SOURCE to FREERTOS_USE_RTC...
Hi,
I have a nrf52832 dk(pca10040 1.2.1), use gpio P0.29, P0.30, P0.31 to connect some external device,
external device working voltage is maximum 2.2v, so I connect external...
While running UART rx and tx calls the uart_callback_set I have set during initialization will stop running. This prevents me from sending or receiving any new UART information...
Hello,
Could you tell me if SoftDevice V7.3.0 can be used in SDK 17.0.2?
According to the following website, you should use Softdevice V7.2.0 in SDK 17.0.2.
https...
Hi,
I use a pca10056 with the "mqttsn_sleepy_publisher" example. Unfortunately, I cant connect to the mqttsn gateway. It throws me:
"NRF_LOG_ERROR("CONNECT message could...
