I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello I'm trying to implement the DFU Trigger library into my project. to get following function:
" When the trigger library is added to an application, it allows a connected...
Greetings,
I am trying to get the nRF5340 DK to run on the coin cell battery attached to it. I removed the plastic and the USB cable then I put the "nRF power source" switch...
Hi team,
When we set fast advertisement timeout (uint32_t ble_adv_fast_timeout; /**< Time-out (in units of 10ms) for fast advertising. */) to a value greater than 0xFFFF...
i am using Laird smartBASIC for my programming of the BL653. I cloned the firmware of the evaluation board using the supplied Laird batch files and the J-LinkARM interface...
Hello, I have a question that I can't find an answer to in the documentation. The answer may be somewhere and I am just unable to find it.
My application utilizes sd_ble_gattc_write...
is it possible add dfu service and central uart both into nrf52820?
using D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c
SDK_17.0.2
Dear Nordic Bluetooth experts,
In the Android-nRF-Mesh-Library , is there a way to mark a unicast address as used? The reason why I'd like to do it is the following: When...
Hello, All,
I am using nRF9160 for product development and would like to know a few more important parameters:
What is the power consumption of an NB-iot network using...
Hi There,
I want to connect programable pins on nrf52840 chips in the schematic.
Can you tell me which pins are for programming and debugging?
Best,
Gaosheng
What does this error mean?
<error> app: ERROR 3735928559 [Unknown error code] at c:\nrf\modules\nrfx\hal\nrf_gpio.h:492 PC at: 0x00033D23 <error> app: End of error report...
We need to update our app to accommodate Android 12, but the DFU library has not been updated and crashes when we initiate an update.
Full details are in github-bug: https...
Hi,
we want to run your example of AoA
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_connectionless_tx/README.html...
API doc says
Specs says:for ed_threshold:
PRF[dBm] = ED_RSSIOFFS + ED_RSSISCALE x VALHARDWARE
ED_RSSIOFFS is -92, ED_RSSISCALE is 4.
So if I want to set the threshold...
