Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
hi...
i am using nrf52840 , segger.... mesh sdk 3.1 version in this case i want to send the simple message from client to server .how to do this ?
suggest me an idea ...
Hi,
I have some of peripherals at 1.8V and some at 3.3V that I'd like to run off the nRF5340. Is there a way to selectively set which interface is in a specific voltage...
Description:
We'd like to extend our existing bootloader. It currently supports UART transport and we want to retrofit a bootloader that also supports OTA via BLE. On merging...
I am testing the nRF9160 DK. I would like to know which SIMs are available in Japan.
I have confirmed that Sakura's Secure Mobile Connect SORACOM(Plan-KM1) works.
I'm...
I'm sorry if this has been answered somewhere else, but I couldn't find a thread that specifically addressed this.
Looking through the Modem FOTA options there is the...
Hi,
I'm working on a design with nRF52840 on PCIe Mini Size card. Since there is no VBUS rail on PCIe connector and I need a communication via USB, is it possible to bypass...
I see that I can USE BT MESH in an application . Can I encrease the number of advertisingh channel adding some secondary advertising channel?
May I do that in this way ...
Hello,
I come to you because I did not find the information on the web about sending MQTT data. I send a buffer of size 1408 with MQTT but I see in the configuration that...
Here is a screenshot of my current debug session. I cannot figure out why this if statement is failing. I have circled the relevant information. Even the disassembly indicates...
Hello,
I am trying to debug and develop in the net core of the nRF5340 and am having trouble flashing and debugging from SES.
I started by following the guide posted here...
Hello,
My board is connected to Gyro, Magneto sensor.
And board is sleep and wake-up by GPIO.
It usually works well. But time to time after wake-up from sleep mode...
Good Morning!
I try to update the modem firmware of a nRF9160 chip.
When I connect it with the nRF Connect v3.6.1 - Programmer (v1.4.10) and try to update the modem with...
Hi all
For the nRF52832, the total maximum sink and source current is recommended to be 15mA in this devzone entry .
Unfortunately, it seems like there is still no value...
I want to add an external button that mimics the properties of the buttons in the nRF52 DK. I read that the switches are all active low, so I assume that this means they are...
Hi,
in peer_manager.h and id_manager.h the docs say a function can return
BLE_GAP_ERROR_WHITELIST_IN_USE
But the error code is called
BLE_ERROR_GAP_WHITELIST_IN_USE...
