Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi Nordic Team,
I would like to share with you a minor challenge that we are facing to use the nRF52840 dongle with a Zigbee Mesh network and issuing a serial communication...
Hello,
Does anybody know where I'll be able to find an EAGLE library for the nRF52840 CKAA chip (the WLCSP-93 package)? I've looked around and all other dev boards that...
Hi,
I'm having doubts about whether to use NUS or OTS to transfer 500 bytes of data from the peripheral device to the smartphone. Regarding OTS, I've tried using the ble_ots_central...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as a central and Android device (Bluetooth 4.2) as an advertisement.
During development, I was wondering...
Hello,
Following is my hardware and firmware setup.
Thread BR:
PCA10100 v1.0.0 connected over J-Link microUSB port to RPi 3B+
SDK v4.1.0
Thread Node:
PCA10100...
Hi,
If using a serialization connection to a BLE module. The application will run on the host MUC and the BLE module only runs the SoftDevice (BLE stack). I understand that...
I'm running the unmodified blinky example on the 52840 dongle PCA10059 and it connects just fine with the nrf connect app but will not pair with the phone via the Android...
Excuse me:
When I was testing the OTA of nrf52820 chip, there was a download error in the command line tool。Here are my steps in nrfjprog tool：
1、nrfutil settings generate...
Hi,
I am running the Mesh Light Switch Example Code on My custom board (nRF52840) by changing the BSP_ LED_0 from 13 to 33(LED pin no on my custom board) pin number,but...
Hi teams,
I am trying to implement Decawave DW3000 functions to nRF52833DK as host.
Decawave provides some APIs for nRF52840DK, and I have succeeded make it working on...
nd Since i am still a newbie to nordic i wanted to know how can i break the task in smaller steps.
1)As a first step i get the values in temperature form using saadc.
...
Hi,
I am unable to find how is software interrupt generated for Softdevice.
I am able to see SD_EVT_IRQHandler()
but when this event is triggered
Sudhir Foujada...
Hi,
I am using sdk for mesh V.5 and nrf52840 dk.
I have run the serial mesh example and it worked fine.
I also modified the light switch example to send and receive...
