Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I continue to be confused by the Nordic setup of projects. There are a bunch of different demos, but what if you want to compile features from different ones?
Specifically...
Hi ,
I have used Calendar example running on RTC2 for my timing feature .
Below are the initializations for starting RTC2 for my clock .
#define CAL_RTC NRF_RTC2 #define...
Thanks in advanced. Both platforms are: nrf52832, sdk17.0.2. The peripheral is based on ble_app_gls and I set static passkey 123456, the central is based on ble_app_hrs_c...
HW: nRF9160 DK
SDK: nRF Connect SDK v 1.4.2
Hello, this is to report a buggy behavior I encountered when trying to implement a BLE-LTE gateway on nRF9160 DK
First...
I want to move the UART on thingy91:nRF9160.
prj_thingy91_nrf9160ns.conf added the following two line.
CONFIG_UART_ASYNC_API=y CONFIG_NRFX_UARTE0=y
The asset_tracker...
Hi All,
I want to use DFU to update the firmware from central to peripheral over BLE , both central master and peripheral are nrf52840.
Central master can find unknown...
Good Day,
we are currently working on a project for university. For this project, we are using esb to transmit a continuous audio stream (i2s format). We sample our data...
I've read similar issues but none with this configuration:-
nRF Connect SDK 1.4.2
Blinky example
Trying to enable RTT logging
nRF5340DK board
Windows 64 bit host...
Hi,
I've come across a situation where when paired to Android 9 devices, the reconnect event that follows waking the peripheral fails. Connection parameters are
The...
For ble_gap_adv_set_configure_req_enc, is the document provided?
I saw " ">infocenter.nordicsemi.com/.../group__ble__gap__app.html" , it was not found.
Hi, There is problem that the including file from "openthread\third_party\NordicSemiconductor\libraries\fds" and already added its path to file...third_party\NordicSemiconductor...
Regarding the data encoding in Advertising, the order of the data is different depending on the SDK. Is there a problem in operation?
The confirmed function is as follows...
We are using nRF52811, is there any sample code support to set/save thread power calibration table/data to available non-volatile partition.
thanks, Webber
Hi there,
Can we please get an updated example for Appendix 5 in this blog ?
Specifically the DFUMaster_SPI and the bootloader_secure_SPIS. Ideally it would be compatible...
Hi!
I was trying the throughput example using two nRF5340PDK boards and I observed the throughput is very low, i.e. 1kpbs. I tried programming the cpuappns, but it didn...
