Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm trying to figure out why my Xbee3 module can't connect to my nRF52480 app. I built the app using SDK 7.2.0 and Segger and it runs great. I can connect to it from nRF tools...
Hi,
I am using app_timer and SoftDevice in NRF52810.
I am storing app_timer_cnt_get() value after releasing button and after completing BLE Advertisment.
as I am starting...
Hey all,
I have started working with this board around a month ago, and start to understand it little by little. I have a program that communicates with a display over UART...
Attempting to program an nRF52840 dongle with sniffer_nrf52840dongle_nrf52840_7cc811f.hex, using nRF Connect Programmer v1.4.8, on Windows 7
Upon clicking "Write", the red...
HI,
I am trying to use STTS751-1DP3F temp. sensor with nr52832. The drivers for sensors are given on:
https://github.com/STMicroelectronics/STMems_Standard_C_drivers/tree...
I have some old production code that uses s110 v 5/6 and SDK 8.0.0 (perhaps - no one seems to know). The production device has never been able to do a bonded reconnect correctly...
Hi,
Your online power estimator only concerns nRF52840/832/810.
How to get a value when using nRF5233 with CTE activated for AoA ?
In other words, what is the additional...
I'm trying to create application for working with nRF52 device. I have completed provisioning mesh success, and receive notification message about success operation (work...
I know that SoftDevice 110 is old but I am stuck with it as it is on a production device with nRF51822. For some reason when I call sd_ble_gap_adv_data_set() with a non NULL...
I am developing software with the following features.
Communicates between two boards with nRF52840, nRF5 SDK 15.3.0, and its S140
Activate both extended advertising...
When I use this setup, when the specified duration expires, should I get a BLE_ADV_EVT_IDLE event? I don't seem to get one, even though I'm testing for it. SDK 17.0.2 / S...
Hi,
I have 4 sensors on my custom board and I'm planning to use BLE. I want to read data from all 4 sensors every 200ms. I'm planning to use app_timer for that and read...
Hi
Using demo usbd_cdc_acm and found a very strange bug!
Even I disabled the flow control of uart , the 52840 device still need to control the DTR signal to ensure UART...
