Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am using nrf52832,I have Defigned "CONFIG_NFCT_PINS_AS_GPIOS"as below。P0.09 is configed as POWER_HOLD pin, P0.10 is configed as buton.
I found that when I download softdevice...
Dear Members,
For scanning GSC10 sensor,
can this example be used ?
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ant_examples_scanning.html
Thanks
Hi,
I am currently working on the project that involves Pre-certified Bluetooth Module (SG Wireless SGW1110 CE & FCC certified, based on Nordic Semiconductor nRF52480)....
I am getting an intermittent "Softdevice assert: 151994:0" error on device initialisation or after the device has run for a period of time. I am using Light Switch Client...
Is there a way to generate a square wave like the one in the picture without using any kind of interruption to change settings middle-wave?
For example, the wave can be...
Hi,
I have been able to use the NRF-9160: Cloud_Client sample for sending data to my AWS IoT MQTT broker on PSM mode from my Thingy91 with a CLOUD_MESSAGE_PUBLICATION_INTERVAL...
Hello, I am trying to implement my own custom bootloader in the nRF52811. I have the softdevice loaded, which then jumps to address 0x19000. This is where I put my bootloader...
Hi,
I'm using nrf52833, flashed by using Jlink SWD programmer. I have no probleme to re-programmed 2/3 of my board.
But the hird gave an error. The strange things...
I am using the gazell protocol of nrf52840 to achieve some functions,but I don't know how to understand the protocol code deeply,anybody has advice or flow chart or relevant...
I want to implement noise sensor based on PDM (pulse density modulation) , But I cant found any PDM driver or API based on Zephyr , I used MP34DT05(st semi-conductor).
So...
I have nrf52832 radios communicating with each other 100%. I have a nrf24l01p that is the 'gateway' to which the nrf52832 sends dump data. I can communicate with nrf24 and...
When i start the nRF mesh app, it crashes immediatly. What do i need to do? I re installed it a couple times and i rebooted my phone a couple times.
The phone is a samsung...
Hi,
I am developing firmware both nrf52 and nrf91.
in nrf52, I activated BLE, usb and uart. Uart communication established between nrf52 and nrf91.
in nrf91, I activated...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag). I can able to control led's using customized board. But Bluetooth is...
