I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi there i have serius problem in gettimng my nrf52840-dk to work, i am set up in Visualstudio code on a mac, avery thing compiles and seem to upload but nothing happens afterward...
nRF connect v1.0.0 SDK
I am using UART peripheral to communicate with GPS module and we want to put device in PSM (Power saving mode) but we are not able to disable UART...
I,m using nrf51822 , Softdevice S110 and SDK V10. i have and spi interface with SST26VF064B (8MB flash) . SPI is running at 4MHz frequency and there is 8us delay between each...
I have a new board with a STM32L47 running mbed OS. There is an nRF52811 connected via SPI. I simply want to verify that the nRF52811 is connected properly and can be communicated...
Hi there,
On our test jig, we are using two IO pins of nRF52832 as UART lines that goes to a UART dongle to the PC. When we pull the power plug to the Nordic chip and have...
I deleted nrf-related files and set up nrf programs from a scratch following Get Started Assistant of nRF Connect v3.0.0
I've got this warning when I opened a project by...
This is for a current project on SDK 15 and nRF52832.
My project has several configuration parameters, which exist as BLE attributes.
I'd like to make them persist across...
Hi,
I am study nRFGo Gazell now and I got confused on timer period change in gzll_radio_isr_function().
Per my understanding the Gazell link layer modify timer period...
Using nRF connect SDK V1.0.0
File --> Open nrf connect SDK project
Tools --> Option --> nRF connect
Install all the packages described in "Getting started...
We are evaluating the feasibility of a device using nrf52840 which requires below peripherals:
3 x SPI: For MCU to MCU communication + high-speed data transfer from sensors...
Hi,
I am using nRF51822 controller. And I am using SPI peripheral to read 80 bytes of converted data from an ADC converter.
While reading spi data I realized that there...
Hi,
I have build a application based on the mqtt-simple-sample and successfully integrated TLS.
Now I wanted to measure the floor current in PSM. I did wait some minutes...
Folks,
I have a dev board PCA10040, which is running, I think, soft device s132. Additional load file is:
components/softdevice/s132/hex/s132_nrf52_6.1.1_softdevice.hex...
Dear Team,
I have a problem with one sensor on some boards, the behavior is not clearly reproducible. On some boards, the "device_get_binding("CCS811")" just delivers exit...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
