I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
hi ....
i want to test the bidirectional working , i am using uart peripheral example , i have taken the rxd,txd,cts pin from Nrf52840 board interfaced with TTl uart .....
I am working on nRF52DK. This will act as peripheral device and smart phone device will act as central. From my observations i could see 48-bit mac address and GATT local...
Hi
I'm currently doing an internship about bluetooth mesh network.
I'm using the light switch example with a client board and a server board, provisioned with the nerf...
We have an interesting difficulty, whereby after a period of time which varies never longer than 12 hours, often around 6 hours, our application disconnects from the network...
Hi,
I have NCS v1.0.0 on an NRF9160-DK v.0.8.3 and I am trying to run a program written before the SDK update. I can build and flash the program but when I try running...
Hi. I have a multilink central based project running on nRF52840 SDK15.0. I have added code from another example to do advertising as we want the central to advertise some...
Hi ,
I am build and run the source code of nrf Uart app from nRF UART App git repo. When I clicked on the connect button it opened a new sub window ,I know it is the list...
Dear all,
we would like to use nRF9160 DK as a CAT-M1 reference device for our local test purposes. Usually we use iperf tool for UDP traffic generation. Do you have any...
Hi,
I try to use the nRF52840 as a sniffer. I tried to follow ( https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf ) but I block in the 2.2.5 part.
When I run...
On the NRF52810_PS page, I find UART is exists,
But on the sdk_15.2.0, NRF_UART_Type is disappear at nrf52810.h.
So I can't call any nrf_uart_xxx functions and UART...
Dear All,
I know similar questions have been asked before but I have read around quite a bit and I couldn't find an answer to my specific problem.
I have a ble application...
Hello All,
I am working on the simple advertising example.
I am using SDK_V_15.3 and NRF52 DK board.
I want to create a timer for on / off the advertising repeatedly...
Hello,
I have successfully flashed and run the mqtt-simple example from the nrf samples with the default configuration.
If I run it 10 times in a row, the getaddr with...
Hi.
I struggled to migrate ble blinky example of nrf5 (nrf51422) to nrf51822 using KEIL (SDK5 v12.3) but failed
Here are what I tried.
Firstly, I changed target device...
Hello,
I want to create a program for communication and control between the NRF module and the desktop. I followed the instructions Installing from https://github.com/NordicSemiconductor...
