I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello everyone,
I started porting our software from NRF52830 to NRF840.
I am currently stuck with a weird problem: I a unable to use and configure PINs of the NRF52840...
Hi,
I wanna automate the processing of compilation, my idea is to point all path-related files (*.c and *.h), I wrote script which is looking for all *.c and *.h files and...
Hello Nordic team
I am working on nRF52832 Dk, SDK v15.2, example "ble_app_buttonless_dfu".
Following code snippets is the GPIO configuration for pin interrupt:
ret_code_t...
Where can I find the hardware files (PCB, board layout, schematics, etc.) for the Thingy?
There seems to be a vague reference to zip file but no link.
There seems to no...
Hi All.
We are trying to do DFU on a device using s132_nrf52_5.0.0_softdevice.hex.
The DFU interrupts first time when it is around 15-20% complete.
When the DFU is attempted...
Hi!
I am using nrf52840,sdk 14.2,Keil IDE
I am using bmp180 and mpu6050 sensors.
In proximity code,I have integrated both sensors separately,It works fine.
But while...
Hi all
i'm new in both this site and nrf52
i have a question
Is there ADC CONFIG register in nrf52? i can't find ADC_CONFIG in nrf52
NRF_ADC->CONFIG = (ADC_CONFIG_EXTREFSEL_None...
I have an application where I am sending a fixed packet length of 32 bytes to data pipe 1.
I have set the data width to 32,
I have auto acknowledge enabled on P1.
I...
Hi,
I designed a nRF52832_xxAA board, I can't find the bluetooth name in iphone - settings - Bluetooth - Devices, but I can read/write and notify in myself mobile app and...
Hello,
I am using sdk version 15.2.0 and nrf52840. In the application NAND flash TC58CYG2S0HRAIG is used. We are using flash to store values which we receive from the USB...
1.I want to know whether there is any existing network in the same channel .And get the existing network's information like PAN ID.
Any APIs to do this?
2.How to set...
Hi,
I'm trying to run a display using SPI, and I've run into some troubles. I've attached my code below:
My issue is that the program never gets past the while loop...
Hi,
I am getting the GATT ERROR during init packet stage during firmware upgrade. I am using SDK 14.2 and nRFConnect application on Samsusng Galaxt S8. It looks like I am...
