I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to do things like
get the current date and/or time
configure a socket
activate a socket
Usually I use commands like
at+cclk
at+csdf
at+ctzu...
I am following the Thingy:52 "Compiling With Keil" instructions provided in the following link.
nordicsemiconductor.github.io/.../firmware_compile.html
However, I get...
Hi,
We have released multiple products with the NRF52832 chip with SDK's ranging from 10.x to 14.x, quite successful so far.
However, one part that is lacking in my opinion...
I have been struggling with getting nrfjprog working on CentOS 7.x. Each invocation results in the following error due to the version of glibc used to link the nrfjprog binary...
Hello!
A quick question about how to shutdown unused RAM on the nRF52810-CAAA?
We're not using any of the Soft Devices. Our code is pretty tiny. Map file attached.
We...
Hi,
I want to read data from my ble UART (NUS), to do that I implemented the NUS service and registered the onDataWritten callback (which is the MBED equivalent of the HVX...
Hello:
If we are to use the nrf9160 in a production product, what additional certifications are required? For example, if I purchase a Telit cellmodule, I still have to...
Hello All,
I want the DFU service at the application level, not at the bootloader level. Means I have to build a very simple bootloader but I want DFU service at the application...
Hello nordic:
nrf52832 how to control pa, i use this functio pa_lna_assist(). This function is the solution on BBS.this used for s132,but i use s332.the ble is ok,but the...
As per description, I don't understand how to make a dfu package that writes the whole MBR+Application range and doesn't use a SoftDevice, for example out of a hex file such...
I'm using SDK 15.2 and trying to set up a USB mic class. I am having trouble getting the SOF audio interrupt to fire.
I initialize the app_usbd module with the configuration...
Hi
I would like to know that is there any Blue tooth low energy relay like RFID tag , which can detect bLE only and can trigger a circuit. It should have small form factor...
Hello everyone , i have noticed that the sniffer can pick up the the packet from the same channel twice.
According to the Bluetooth 4.2 specification, the advertisement...
Hi all,
We were developing our application using nRF52840 and later decided to change to nRF52832 considering our hardware constraints. nRF52840 has 16 bit counter for EasyDMA...
Hi all,
I want to make a 2.4g wireless keypad usb reciever application, I tried to found some offical software demo but get nothing, is there such demo supplied officially...
