Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I'm trying to create more groups in mesh.We know that all the nodes(servers) are divided into two groups called ODD and EVEN,so I want to create more groups.
I have changed...
I posted recently ( https://devzone.nordicsemi.com/f/nordic-q-a/40381/interfacing-with-mcp4725-with-twi-registers ) and after editing the post, I can no longer access it ...
Hello, boss, I used twi read/write data from others device, I find a strange problem, When in no-blocking mode, mainly loop use "sd_app_evt_wait" TWI can't write data to others...
Hi, all. I have been going through the mesh examples and have been able to do the light switching, dimming etc examples and have used the RTT as well as physical buttons to...
Hello everyone,
My problem is the next one :
I bought a Nema 17 stepper motor (this one : https://www.pololu.com/product/2267 ) and it’s driver (this one : https://www...
It appears to be an error in the function signature `sd_ble_gatts_hvx()`.
Since the call is made via software interrupt, the const qualifier is cast away regardless.
So...
I am trying to implement the HAL interface for USB devices in Mbed for the nRF52840. Mbed is currently on nRF SDK14.2 so I may not have all the most recent bug fixes for the...
Hi,
I would like to run a different LWM2M client other than leshan LWM2M. Could you please answer me following questions:
i) Can i run any other LWM2M client written in...
Hello,
To improve the performance of SAADC, I would like to isolate the SAADC from the bad effect of DC/DC and RF.
I assume that SAADC has some noise because of DC/DC...
SDK 15.2's scanning module tries to connect to advertising peers that pass filter criteria when the nrf_ble_scan_init_t connect_if_match field is set true even when the advertisement...
Hi Forum!
I have to understand NRF52 chip for my job! I used to work with STM32 before. It has "Interrupt" (e.g when I receive one byte via SPI, It generates one "SPI_Rx_Interrupt...
Hi, all. I would like some serious help. I have three nRF52840 boards and have been running all the examples from the blinky to light switch/dimming. I am, however, stuck...
Hi,
could you please explain me what nrf52840_peripherals library (located in nrfx folder) is actually doing and what do the numbers next to the definitions mean ?
I see...
Hello everybody, As part of the evaluation of the nrf52840, I have made range measurements. In the course of this I was also concerned with the question to what extent the...
