Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
What unique information can I use to know which physical device disconnected for example? Say I have a MAC address or a name encoded into the advertising packet. Correct me...
Here the connect method is called
err_code =
sd_ble_gap_connect(
peer_addr,
&m_scan_params,
&m_connection_param,
APP_BLE_CONN_CFG_TAG);
In the ble event...
I'm tring to connect my phone to the multi-connect example client app
I'm tracing the ble events in the ble_evt_handler.
When I open the server app on my phone, I see...
Hi Engineers!
faced with a problem of SAADC impedance too small (4,7K)!
We use SINGLE ENDING 8bit mode with following settings:
NRF_SAADC_REFERENCE_VDD4
NRF_SAADC_GAIN1_4...
We are moving from a PCB using a nRF51822 QFAB module to a newer PCB using an nRF51822 QFAC module.
We observed that with the new QFAC PCB we have a significant connection...
I want to use the nrf52dk PCA10040 to remote program a BC832 chip from Fastel.
They say:
"BC832 V1 pin B3 C3 (DCC, DEC4) needs to be connected to the program can be burned...
I have an nrf52832 BLE HIDS device based, with the connection and peer handling code copied from the hids keyboard example, SDK13. I use Windows 10 as host. Setting up a connection...
I plan to keep the bonded device information in the ring buffer, but there are a few things that puzzled me:
When PM_EVT_CONN_SEC_CONFIG_REQ event is received, .allow_repairing...
Hi,
i am working ANCS example project in nrf14.1.0 SDK, s132.5.0.0 softdevice. i am able to print category of all notifications. i wanted print text message info. is it possible...
SDK13 nRF52 S132.
Hi! Correct I understand and implemented how to make interrupt?
I use gpiote.
void gpiote_init (void)
{
nrf_gpio_cfg_input(INT1, NRF_GPIO_PIN_NOPULL...
Hello,
I am using sdk12.2.2 and nrf52. I am including scan response data in my packet. But every time I am getting extra fields in my raw data as seen in nrf connect app...
Hi
I discovered I strange behaviour using twi.
I am using sdk-14.2.0, and Segger Studio. I started with the twi_scanner projected that I found in examples/peripherals...
We are using the NRF8001 in a product that is potted in epoxy with wireless charging and so completely inaccessible to any outside inputs except through bluetooth. We have...
I have already configured the usb audio class for NRF24LU1+.Then if i want to send data throught the NRF24LU1+ USB Isochronous endpoint,what should I do? Actually I have already...
