Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I am trying to use the nrf_drv_twi class but I cannot define a nrf_drv_twi_t instance. When I write the code
`nrf_drv_twi_t twi = NRF_DRV_TWI_INSTANCE(0);
I get...
Hi,
It is indicated on page 59 of the datasheet (rev1.0), concerning the register nr.8 OBSERVE_TX, that "the counter PLOS_CNT is reset by writing to RF_CH . See page 75...
I am working with SDK12.2.0. I see that transports seem to be registered as section variables with the identifier dfu_trans
I have added a section definition in flash to...
Not sure if this is a typo in the function comments or a small bug, but thought you'd probably want to address it either way. I'm on the most recent NRF5-SDK (12.2.0) and...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Gentlemen,
I'm trying to develop a Health profile solution that works with Win 8.1
I'm using SDK 6.0 and S110 v 7
Win 8.1
I found the Win 8.1 sample app...
I am looking at the Master Emulator examples ProximityDemo and HealthThermoDemo. I can use both to connect to one device that I have (Device A). I try to use ProximityDemo...
Hi,
I want to achieve DFU OTA nRF51 using NRF52832.Is it any example,or data transfer message sequence charts documentation? Could you give me some suggestions?
Thanks...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi,
I hope you are doing well. I am working on nrf51822 project. I want the nrf51822 to advertise for 5 secs and then sleep for say 30 mins or an hour and then wake up...
hello,
Starting nRF 52832 (s 132), leaving idle, after 3 minutes, ble_event_id 0x1b will occur, then BLE communication will be impossible.
When ble_event_id is 0x1b, how...
Hello,
I'm having special SPI protocol which requires SPI Slave to toggle REDAY pin after every byte. I do test using 2 nRF52 boards. One is SPI master, another is slave...
Hello all, first time using a I am using a nordic board im a little overwhelmed by all the options. I have nrf51 development kit and I just used the getting started tutorial...
I'm starting a new design on nRF52 and I need to connect a microphone on it. Reading the datasheets and questions here, I found there's 3 solutions for the type of microphone...
