I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi guys. I have a EVK_NINA_B1 board which is based on nrf52832 and SDK12. I am trying to run the ble_peripheral/ble_app_uart/ from examples. I can send message through "nrf...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
Hello,
My name is krishna,
I have couple of NRF24L01+ modules,
I am trying to implement MultiCeiver in the NRF module.
The problem is i am able to receive or transmit...
Hi,
I am trying to compile the ANT Broadcast Tx Example from the latest nRF5 SDK v12.1.0 (../examples/ant/ant_broadcast/tx), but I get the following 3 error messages with...
Hi,all
I use nrf51822 connect with ios device,it will automatically disconnect when links more than 90 seconds.
device connection parameter as follow:
#define MIN_CONN_INTERVAL...
Hi I'm using the Jlink to program nRF52832_XXAA, by using nRF command V9.0.0 nrfjprog
I success in erase , but I can't program correctly,I tried Jlink version 5.12g and 6...
initially we developed code for arduino mega board but now we want to use the nRF51822 soc,so how i can utilize my arduino code for nRF51822 ....i have gone through the some...
Hi,
I'm trying to load the secure_debug bootloader for the nrf52 with the SD 132 3.0 and an aplication.
But when I load the aplication the bootloader gets erased or overwritten...
I've got a problem to change polling method to interrupt notification on open-mesh with freertos project.
The example "BLE_Gateway" of open-mesh as flow:
if (rbc_mesh_event_get...
