Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello, I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated Continuous...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
Hi,
At command, I'm sampling ADC for a short period of time. What I noticed is that the current consumption of the chip goes up 2mA, even after the sampling is stopped...
Hi,
What is the actual difference in hardware between the two chips? I know they support different soft devices but is there any actual difference in the hardware? Or is...
Does having monitor mode debugging or using RTT print statements increase the quiescent current of the nRF52 even when the debugger isn't connected? I am using S132 SoftDevice...
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK 6.1...
Hi,
I use an nRF51822 QFAC A1 and my goal is to disable BLE in a powerdown mode, then when I press the pushbutton I want to restart BLE.
Tried using BLEDevice::shutdown...
Hi,
I'm using nrf52 dk(PCA10040). I want to disable the SAADC between readings to save power. I am calling the function nrf_saadc_disable() to do so. It seems to disable...
Hi,
I am having some trouble to make NFC Tag emulation working with "ble_app_hrs_rscs_relay" example application in the nRF5 SDK v11.0 on a PCA10040 board. Actually I did...
Hi all,
i have a little problem with the #define NRF_LOG.
I have this warnings, and i don't know why.
Warning[Pg004]: macro parameter " VA_ARGS " is used in both expanded...
Hi,
I would like to generate PWM waves with on/off period as low as 10usec.
How to stop the PWM and restart it? I tried this but does not stop the PWM:
void pwm_start...
I am trying to advertise my eddystone UID,TLM and URL frame on advertisement. Here by board is in peripheral mode.
I used radio_notification_init() function where i have...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
