Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hello Everyone,
i am trying to simulate the circuit using Proteus so can anyone tell me where can i find the Pspice model files for the Nrf51EVB is it available? any suggestions...
Hello to everyone.
I write code for NRF24LE1 using KEIL and rtx tiny. But i have some problems.
When i power on my device, programm don't run correctly, but when hard...
Hi experts,
The softdevice is s120. I get error code BLE_ERROR_NO_TX_BUFFERS after calling sd_ble_gattc_write() several times. I want to ask what does the tx buffer mean...
I have a strange problem on my target nRF51822. When I try and use the UART interface between my nRF51 and my host MCU, it causes the nRF51 to reset and the RTT terminal to...
Hi,
I've been playing with NFC on nRF52. It sends "Security Manager TK Value" over NFC. There is currently no option to use LE SC over NFC in examples, which is to send...
Hello
I have an problem using I2C on my custom board which uses an Nrf51422 SOC.
I have an RTC chip connected to it and I have no idea how to use your libraries.
The...
Hi! I'm using Arduino BLE micro and good results so far. With some accellerometers connected via I2C.
Today I have a strage behaviour.
I connect the arduino, ok, open...
Hello everyone,
I have a nRF51822 dev board connected through USB to my PC.
I have connected it to COM5 using Terminal and now I would like to interrogate BLE like we...
Hi guys
I have a custom board with NRF51422QFAA, load "s310_nrf51422_2.0.1_softdevice", program on "nRF51_SDK_7.2.0"
the bootloader I used is "dual_bank_ble_s310"
...
Is there a way to control the max # of packets be transmitted in one connection interval?
(We want to vary it from 1 - 6, knowing that nordic can support up to 6-7.)
Has anyone had any success setting the configuration register on TMP102/112 temperature sensors via I2C? I'd like to switch the sensor to one-shot mode to further minimise...
Hi everyone !
I'm trying to send data from an nrf51822 to an nrf24l01 with arduino and I guess I'm doing something wrong...
For the moment I succeeded to have these talking...
I have a simple ANT beacon application.
UART will be enabled to do some communication. How can I turn it off before ANT goes into sleep mode? Is there a call back function...
I want to send a set of 64 bytes data with ble. as I understand, the max data length I can send within a characteristic is 29 byes. when I send 4 bytes data it works fine...
