Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm implementing a custom service with one characteristic and 128-bit UUID.
I am able to set the custom base UUID using sd_ble_uuid_vs_add() but the resulting bytes look...
Hi,
I would like to know can i configure advertising interval for more than 10.24 seconds.
Which are the functions i can use for configuring advertising interval.
Also...
Hi All,
Yesterday while (unsuccessfully) trying to get my dongle to work with Antware II, I did something I'm not sure what it was, but has caused the following:
MCP ...
I'm developing application on nrf51 for that i'm using...
SDK : nRF51_SDK_8.1.0_b6ed55f
Board : PCA10028
I'm trying to run code from SDK examples C:\nRF51_SDK_8.1.0_b6ed55f...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
every time I try to add a new example in Keil microvision, it dont work me.
last time I try to import a new pack, I got this error:
pack instalation failled...
I use SD 7.1.0. My own app works perfectly. I use my own PCB, debugger J-Link Segger.
I try to upload any app via bootloader from SDK's example (modified in LED_pins dfu_dual_bank_ble_s110_pca10028...
I'm trying to send over a ble the data for a tablet
I'm trying to use the example of analogues (NordicSemiconductor/nrf51-ADC-examples) an old time I get error response...
Hi,
While calculating the power consumption according S110 soft device specification only ION current has been considered.
So does ION include current consumed by DCDC...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
i work with the nrf51 example for ble and sd130 (nrf51 dongle and sniffer) and now i like to use sd310 for ble and ant+. is there also a example for sd310 (or sd110)?
Th...
Hello everyone,
I am using ADC functionality with NRF51822 and its working fine, Interrupt is raising when ever i give input to Analog Pin. Communication protocol i use is...
Hello.
I'm trying to start developing with the nRF51822 Eval kit with Eclipse and ARM GCC but I ran into some problems when trying to run the ble_app_hrs_example. I've been...
