I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
We're a bit troubled by the known issue NCSDK-20567: Partitioning limitation with MCUboot swap move , and are trying to find a work around.
Since the issue is with...
Hello
I am trying to implement AoA reception using the TimeSlotAPI on the nRF54L15.
I have previously implemented a simple AoA reception function on the nRF52833.
Please...
Hi,
I'm trying to set up two nRF5340 Audio boards - one as a unicast client (gateway) and the other as a unicast server (headset). I have seperate config files for both...
Hello, we've been using nRF5 SDK and nRF5 SDK for Mesh for about 5 years now and we're looking to port our codebase to nRF Connect SDK.
We have already started the process...
Dear Customer Support,
Reaching out for help / example on couple peripheral configurations
We are using nRF Connect 2.5.0
1-UART
we have the following configuration...
I am using a Sierra Wireless HL7800 modem with the nrF52840. I have been able to receive SMS messages and see them come through the RTT log. Setting to text mode and then...
Hi,I am using NRF5340 ,I want to log data of 2 channels of mic with sampling rate of 16000 but while logging I am receiving "120 messages dropped" and with some random numbers...
Hi. First of all, I appreciate to all users support. I work with SDK 17.1, nrf52832.
I`m trying to make multi link Central. It connect to multi Bootloaders for DFU.
When...
Hi, I am using the npm1300 with the nrf9160 with ncs2.7 When we do a reading from the npm1300 to get the current and voltage values, the readings are always delayed by 1 reading...
Hi
I was trying to take code from ble template and put it in my own project. Even after copying the entire main file and including file directories it shows loads of errors...
I want to set serial communication over USB and try to implement CDC ACM functions on nrf52840dk-nrf52840.
prj.conf:
.overlay:
But now, build on NCS v2.7.0 stops...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
We had made our own pre-production PCB, and trying to lower down power consumption. ...
Hi,
I am using download_client to get a bigger file (100KB) to my memory via LTE-M. The Files are located in a bucket and I use a shortURL to get the signedDownload URL...
Hi! SDK17.1 S132 nRF52832
I use hrs_c example and it works. But I added adertising code and wanna use both central and periperial at same time. Works, but until the moment...
Greetings,
I've searched the forum, but haven't found a particular answer. I need to configure the project to not pair with Windows 10 PC because it blocks other software...
