I'm having some issues regarding the data update interval when running the asset_tracker_v2 application, particularly with adjusting how frequently it publishes data to the...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
Hello!
I'm working on a project that was primarily developed with NCS v2.9.0. The application (using an nRF5340) utilizes BLE mesh and is configured to use TinyCrypt for...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
Hi
I am quite well familiar with DECT-NR+ and the Nordic Boards, as well as nrf91xx, we use a nrf9151.
Also some kind of involved at this opener initiative, but I cannot...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
Hi,
Following the course Wifi Fundamenals with NCS v3.4.0. I have an error when building the exercise 2 of the lesson 4 (even with the solution one). I configured the board...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
NCS 3.4.0, sysbuild, with mcuboot enabled.
I want to use a simple custom "my.overlay" for both the app and mcuboot.
For the app it works with
-DEXTRA_DTC_OVERLAY_FILE...
Hi,
I would like to know how to ensure that AP-protect is disabled for application based on 17.1.0 nRF5 SDK.
I've understood that the procedure is:
1. recover the device...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello Nordic community,
using nrf5-sdk for nrf52840 SoC, I followed the uart example as below.
The uart tx and rx works fine BUT NOT THE HWFC
eg. When the CTS is set...
Hi Nordic Team,
Below are the configurations that I have done for the nRF21540 FEM.
.config file
#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
