Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
We are using the nrf51422 qfn 48 and nrf51822 qfn48 in a design.
I understand with the QFN48 we should use BAL-NRF01D3
devzone.nordicsemi.com/.../nrf51822-moving-from...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi Nordic,
We are working on Android and iOS apps. Currently using S3 with Android 4.3 and Note to communicate with nRF51822. Baud rate of 19200bps for our serial communication...
Hello,
Is it possible to increase the accuracy of the advertise interval? Im attaching an oscilloscope screenshot showing the S110 device advertising with a 20ms interval...
Hey All,
I am working on a board that is based on the nrf51422. The system goes to sleep and gets woken by an interrupt. One of the programmers claims to have managed sleep...
We use nRF51822 with S110 as a peripheral connected to iPhone master and looking for RSSI.
RSSI with correct value is received by the peripheral application every about 1...
Are there any sample applications that use a joystick press as an interrupt instead of a button press? The dev board I'm using uses the nRF6350 display and I was wondering...
Hi
I used the example from nrf51822_v4.4.1.31827\Board\nrf6310\spi_master_example for my PCA10001 board, as I know the pins configured in this example are for nrf6310 board...
Does anyone know how to implement a wrist watch LCD display? I mean a bare LCD Display, without a pre-build driver (I2C). Can I do it directly or I need another IC to drive...
Does anyone have any solid numbers on the maximum throughput achievable on
the nRF51822 USB dongle that comes with the nRF51822 Eval Kit?
Application - OTA protocol Gazell...
Dear Support Team,
currently I'm working on a custom board which contains the NRF51822_QFAB_A0.
I installed the softdevice (not the most recent version, but a version...
Hi,
I have bought nRF Beacon Kit, and I have downloaded "nRF Beacon Android 4.3.zip", but I can't find nRF Beacon Service source code.
Where is it? Please tell me.
...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
it register a handler, what about restart and run pstorage_register again, how it insure everytime we get the same address for our content in the flash?
before pstorage_register...
