I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...
Hello, everyone.
I use the ble_app_uart on the nrf52DK board and SDK V17.
I would like to send data from the app using RX characteristics of UART service. The function...
Hi all.
I have written an application using a softdevice and I want to analyse an interesing behavior I don't understand at the moment. So I want to record a trace/log of...
hi!
Can anyone help me with code merging of saadc and ble uart.
Basically i have done analog to digital conversion of my sensor value and monitoring it on serial monitor...
Good day,
Studying the possibility of using C ++ on the MCU nrf52840, I met an interesting moment in file "nrf52840.h"
I have added a part of the file which gives me some...
Dear Nordic Semiconductor support team.
I tried to make my nrf51822 DK to talk to Micro:bit by using Gazell library. ( from nRF5_SDK_12.3.0_d7731ad\examples\proprietary_rf...
I am using nrf52832 with buttonless DFU ,SDK 15.0,using fstorage.I want to store some device information in flash,such as serial number,hardware version,these data will not...
In the compatibility matrix , Engineering A must use the "nRF5340 OPS v0.5.0" specification but when clicking on it, only the latest version (0.6.1) is available.
Which...
Hello,
I want to add control over UART to ble_app_blink_c project.
SDK is version 16,I copied <SDK>/examples/ble_central/ble_app_blinky_c folder and made <SDK>/examples...
Hello,
We're experiencing a strange issue where a device we sent to a partner in the US wasn't able to connect over there after rigorously testing this before shipping here...
I am currently using one nrf51dk board that is automatically showing itself on my computer as a mapped storage device with the label "JLINK".
This is actually a board I...
Hi,
I have a ble device that uses nRF52 chip. I would like to know if it is possible to do ble automation on that device.
Here is my setup:
OS: Ubuntu 20.04 LTS
...