I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Our device uses an nRF52840 and we are using SDK v15.3.0 and soft device v140.
In order to optimize power consumption, I want to make a delay function using the RTC (with...
Hi,
We are designing a device based on nRF52840 that implements the Zigbee ZBOSS stack. We are interested to get ZB NVRAM configuration (network id, bindings, reports, etc...
After not having used my Thingy52 for a number of months, I decided to get back to tinkering with it.
When switching it on, it briefly shines a red light and nothing else...
Hello,
I am using the DWM1001 board and would like to receive some bytes over UART to the nRF52832.
I want the device to wait for a certain number of bytes from UART and...
I am using BLE UART and want to incorporate BLE bonding so that IRK keys get exchanged and can resolve the advertisement packet. I am planning to use privacy mode.
Can you...
Hi, I have followed the steps of generating a new .h file for my custom board (save as of the PCA10056.h board, modify the file, then generate a new macro in preprocessor...
Hi,
Is their any method to listen the MQTT-SN topics inside Rpi? I would like to listen the MQTT-SN messages and send it to my own cloud. Is it possible? I have tested...
I am using nRF SDK v16 with nRF52DK pca10040 board and s112 soft device.
I understand that peer manager can remember each peers' CCCD setting following the bluetooth BLE...
We are evaluating the nRF52832 and have the following questions:
What is the accuracy of the internal ADC voltage reference and the voltage regulators?
Are any of the...
I am using windows 10 and have been able to work with the FOTA sample for the nrf9160 for several months.
I needed to update the SDK from 1.0.0 to 1.1.0. I followed the...
I've been trying to get my 6 Thingy:91s up and running for months now, and the customer is getting really frustrated by the many delays.
I first went through a series of...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1.
Till now I am using ‘ble_app_blinky’ example code, modified to my custom profile and tested On/Off...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Whether can I call fds_record_update...
