Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have a question about the sample project "ble_app_multirole_lesc(SDK V14.2.0)".
・ "Central": iPhone 5s (iOS V11.2.2) ・ "Peripheral": nRF52832(SDK V14.2.0, S132 V5.0.0...
Hello Nordic,
I hope you can help me. I'm using an NRF52840 DK development board.
I followed the instructions on this video to enable debug trace in Segger embedded studio...
Hi, I have a nRF9160 DK, and trying it out with my mac connected to the USB. However, I seem not to really connect to it? I've installed the nRF Connect app, and also the...
Dear All
We have implemented the the workaround because of the anomaly 195 for spim3 and it works as expected, but only once! After the following init
we can use spi...
Hi I am trying to init the serial on the nRF52840 Dongle but there are some defines missing in the boards/pca10069.h
I run this on the nRF52840 DK and it works fine.
NRF_SERIAL_DRV_UART_CONFIG_DEF...
How the base address is assigned to NRF_SPIM_TYPE structure through *p_reg which is in nrfx_spim_t structure?, and also please let me know what is the default base address...
Hi,
I currently have a project which triggers a series of SAADC readings from the Timer0 interrupt handler. This part of my program works as expected, however, to add more...
Hi,
From this link https://devzone.nordicsemi.com/f/nordic-q-a/34224/device-does-not-reset-after-dfu I understand that the compiler option flto caused reset issues. Is...
Hi everyone,
I am trying to use Buttonless DFU to reprogram the NRF 52 dev kit OTA. I had posted a question on the forum and had solved that problem: devzone.nordicsemi...
Hello,
We have implemented DFU services in application but getting lots of difficulties for writing own transport layer for Wi-Fi to upgrade firmware from server. We are...
Hi...
i have done the program to read the temperature sensor, i want to get the temperature in float value . i can able to read the temperature in float but i can't able...
Hello Nordic Pro's,
We are developing a product based on the BLE UART peripheral. We communicate heavily via NUS. There are extended processes that continually send status...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) As per below link, do I need to skip GPIO...
I would simply like to see the debug outputs (NRFX_LOG_DEBUG) the NRFX_TWIM.C module using RTT debugger through Segger J-LINK.
I cannot find any documentation on how to...
Hi,
I am working in nRF52832 SDK15.3 in SES
I need to work on reading multiple Analog inputs. in a different timings.
i have seen SAADC example.
is there any multiple...
