Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
I'm using op-amp(LM358), condenser microphone and PCA 10028.
My project collect output values of op-amp and broadcast that.
But, noise was occurred while it is advertising...
I'm using the ble_app_multilink_central example app.
In the pca10400.h I changed #define BUTTON_PULL to NRF_GPIO_PIN_PULLDOWN.
The problem is that the first pin interrupt...
Hi
I'm creating an android app for smartwatch(used nrf51 ble),I have two questions
1.I used ANCS(Apple notification center service) in my android app,but nrf51 device...
I'm using the SD (nrf52) MBR to update our custom bootloader, in a battery powered device.We have some custom hardware which is used to disable our LDO, to enter a "Ultra...
Hi Everyone,
Recently I have been trying to measure the current consumption from the dev board.
I have set up the board as instructed by cutting SB9 and soldering SB11...
Hi,
I see intermittent incorrect values from the saadc. The code is described here .
The graf shows battery voltage in mV over about 4 days with one sample per minute...
I am getting following errors when compiling source code in Keil-5. Any one suggest me what i am missing to define symbol?
linking...
._build\nrf51422_xxac.axf: Error...
Hi,
We have devloped PCB based on nrf52832 as beacon.
We have also developed firmware for that and it will advertise for some and than go to sleep mode and after some...
Hi,
What is the minimum number of symbols in preamble nRF52840 has to receive in order to receive full packet on Coded PHY? I can see that it can easily receive packet...
help! Thanks
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
chip:nRF52832
we found that the pstorage's callback will not be triggered when the Bluetooth...
Hello,
Issue : XOSC16M is not Starting and the loop stuck forever in below line
while(!pwr_clk_mgmt_is_cclk_src_xosc16m());
where it checks CLKLFCTRL 's 3rd bit...
Hi,
We have a device needs to support user change the device name. We already finished this function. The changed device name can be store in internal flash, and broadcast...
Is there a signal provided by the nRF2460 that indicates TX/RX state of transceiver suitable for controlling direction of an FEM? Does VCC_PA turn on and off during duplex...
Hello!
We're using the SDK 12.1 ble_app_uart_c as an example for a nRF52 DK as Central application. Instead of using ble_app_uart example for peripheral device, we created...
