I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello All,
I am designing the custom board for Automotive application.I considered nrf51824 SOC for automotive application ,is this suitable soc for my application?if yes...
I have this program running on KEIL 5, what could be the problem with the code and Do you guys have any sample code for mcp9808?
Note- I am using the wired connection not...
I'm using SDK11 and PCA10028.
hrs works well, but did not bond with central(both android(kitkat) phone and iphone) in the nRF Toolbox app, althogh it's device manager ported...
I was wondering if anyone has done any extremely high speed UART work on the nRF51 (or the non-EasyDMA module on the nRF52). I need to improve performance for an existing...
Hi,
I ran the ble central example code on nrf51822 16KB ram version without any problem. But when I run the same code in nrf51822 32KB version, the program flow goes to 0xFFFFFFFE...
Working on my first project in mbed using the Nordic nrf51-dk.
The project utilises a TMP112 temperature sensor and attaches the reading to the service data to make it...
I'm trying to rename my device using s130, but the name doesn't get applied.
I went back to the "roots", ie the HRS sample.
Just before entering the loop, I add a name...
Hello,
I am working on a custom board with NRF52832-QFAA-R7 and trying to run ble_app_uart_c on it. I am using uVision 5.23.0.0
The first trouble that I am facing...
I'm trying to implement usb function on the nrf52840. The moment that I connect the usb to the computer the chip resets.
With gdb debugger i found out where the fault happens...
I have some question about ANCS ,when we trun off the IPhone and turn on the IPHONE.
The notifcation is disabled. I have to turn OFF the bluetooth and ON bluetooth form ISO...
Hi All,
I am a beginner,Can you please explain me what is the role of this line?
APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, m_tx_buf, m_length, m_rx_buf, m_length))...
Hi All,
I am using nrf51422, SDK 12.0.0, an SPI OLED display 128x32, and an SD card.
I want to interface an OLED display and an SD card onto the nrf51422. Although my...
Hi all,
I like build a smartwatch-like device that can receive notifications from my android phone. The bluetooth device has a oled screen and displays what notification...
I need to turn on and off one pin around every 100 us. Time between must be 1 cycle (couple of ns) and can't be interrupted at any circumstances.
Without a softdevice I disable...
