Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Hi, I have recently acquire a nRF52840 preview development board to prototype a USB MSD. With the example provided in the SDK V13, I tested the write speed and it was far...
Hi,
We're working on the connection params negotiation. Therefore we need a timer to go off 2 seconds after connecting to send a conn params change request.
Most of...
Hello, I've obtained and assembled a board with nrf52840 as its centerpiece, I'm here to ask what I need to compile my program for this relatively new chip?
Here is a list...
Hi,
Is there a way to determine which channel is currently being used by the nRF24LE1? i can't do hal_nrf_read_reg(RF_CH) because that function isn't exposed by hal_nrf...
Hi,
What is the best way to read the state of an output pin? I have an LED connected to a pin and want to know in a different part of the program whether the LED is currently...
I am having an app_timer (nRF52832 / SDK12.0.0) that's interval must be changed during its lifetime. I am using following code to change the interval:
app_timer_stop(m_timer_id...
Hi,
I'm trying to use the command "mlme_start_req" to setup the device as a pan coordinator to send beacons to the others devices in the network, but after submit the command...
Hello,
In my application, a peripheral will be connected to many central devices, and the application includes buttonless dfu service.
It needs pairing (encrypted connection...
Hi,
I have a device with nRF52832 and firmware is composed of Bootloader (BL), softdevice (SD) S132 v2.0.0, application and I am using SDK 11.0.
I have created different...
Currently, we are trying to have the nRF51 chip working with a type of capacitive pressure sensor. We did quite a lot of work on searching proper circuits of reading the capacitance...
I have 2 board nrf52840 DK, I now I want to send file ( 1~2 Mbyte) from board_1 to board_2 without use UART. where can I get example to do that ?
PS: I also need example...
I've merged the experimental_ble_queued writes sample code into my project and am testing the long write characteristic with nrfConnect from an Android phone. I get no errors...
Hi,
I am trying to figure out the reboot reason on an NRF52 in order to solve it in the best way.
We have a design with a dual supply 3.6V/5V going through a 3V LDO...
