I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
My NRF52832 runs into the hardfault handler when the sd_ble_gap_conn_param_update() function is called.
I copied the BLE code from the ble_app_template_pca10 project...
Hello,
The Infocenter SDK documentation provides the memory layout used by different SoftDevices: infocenter.nordicsemi.com/.../lib_bootloader.html
Is it possible to use...
Can i process coap and adc data on nrf51 board , so that, based on that system will take decision like turning on/off fan or light etc?,if yes then what is the code and can...
I am confused about the lack of softdevice information for the Gazell examples. I am looking at SDK 10 now having first tried SDK12 before deciding to stay with 10.
As...
hello everyone:
i use interrupt to handle button.and when i init it,the power is increase about 200uA. i think the
interrupt will not increase the power
void gpiote_event_handler...
Hello,
I use the arm-none-eabi-toolchain and have a problem when I am linking.
When I make my project, I get the next errors
path/to/spi_handler.c:180: undefined reference...
Hello,
I am trying to test the BLE example named "Current Time Application" located at ble_peripheral\ble_app_cts_c folder. But i can't find the cts_central.ncs file in...
hai
i am using mbed to program my nrf51822. in my project i need to store some data in flash memory . now i am able to store it using pstorage.h . but when i enable bonding...
I am developing a mobile apps using Nordic . I am seeking for Nordic Semiconductor nRF51822 SDK documentation for objective-c(iPhone) as well as Android too. Is there any...
I connected up +5v to the external power pins of the nRF52dk. I see +5 at TP14.
When I set the power switch to 'on', the board does not boot.
Is there something else...
Hi:
Looking in both SDK12/13 I cannot see any examples related to an HID Joystick/Gamepad.
It looks like somebody asked a similar question here: devzone.nordicsemi.com...
I am using nrf51822(pca10028)
i used the timeslot API tutorial in devzone..and it worked fine but i want to integrate the radio receiver example along with this.
nrf_radio_signal_callback_return_param_t...
Hi
In the SDK13 release notes and even in a few posts in the DevZone the new S140 5.0.0 Alpha2 Release is mentioned. I looked for the download link in the product page...
Hi all
I'm using the GATT server on the nRF51822 with the SoftDevice S130 V2.0.1. I've implemented a service and a characteristic which supports only write requests (including...
Here is my question.
I always disable uart after I send data.
NRF_UART0->TASKS_STOPTX = 1;
NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
this was write in the...
