Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I tried to set a custom key in this way:
... ANT INIT
uint8_t network_number = 2;
uint8_t p_network_key[8] = {0xa1, 0x15, 0xb3, 0x66, 0x60, 0xef, 0x19, 0xa1};
err_code...
Hi there.
I'm woking with sensor in board nRF51822.
Do we have any tool to test oscilloscope i2c?
I want to check the signal is same as what I sent or not.
Thanks...
Since nRF51 is multi-protocol, why don't Nordic provide support for Zigbee? This way, customers can simply buy one single chip and have several standards supported. Are there...
I received a NRF_ERROR_INTERNAL error from a pstorage_store() function. As far as I can tell this error should not result from this function. It occurs fairly randomly. This...
In the examples delivered by Nordic, there is ble_app_hrs in ble_peripheral and ble_app_hrs_c in ble_central. But I cannot find a ble_app_hts_c in ble_central for the ble_perifpheral...
I am using Master Control Panel to check some off the shelf BLE product. I noticed that some of them don't provide characteristic value when I press "discover services". ...
I am using the "nRFgo SDK 2.3.0.10040".
The datasheet of 24LU1P says the size of the bootloader is 2K.
But when I build it in Keil, the build information is "Program...
Hello.
I am using a nrf51822 with sdk 10 and softdevice 130.
It has an accelerometer mma8653 to read the orientation of the chip, I am trying to get the x,y and z co-ordinates...
Hi there!
I have nRF51 DK (PCA10028).
I config GIPO as below:
nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrf_drv_gpiote_out_init...
Hi, I am generating PWM waves using GPIOTE, PPI and Timer. (I cannot use the app_pwm library from SDK 10.0 because there is an intial delay of ~600usec for the PWM to get...
Hi,
I want to generate PWM pulses of width 14uSec(off time) and 42uSec(on time). Is it possible to achieve the above
with app_timer module
without app_timer module...
Hi,
I need to configure pwm with 14uSec off time and 46uSec on time. I had a look at the pwm example in the install directory and also : developer.nordicsemi.com/.../a00039...
