Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
hi all:
Recently, I use nrf51822 as a central to connect some older sensor, but the ble chip of the older sensor did not use nordic, so I have this problem. I develop the...
I have the Heart Rate Service(HRS) program written in embedded c. I connected a two LEDs to nrf51822 board. One LED will start blinking when advertisement starts and other...
How do I write a value to gpregret when flashing the chip?
Basically, what I need to do is be able to detect the first time the chip is powered on so I can go into a special...
In my device I want to adjust the slave latency connection parameter, however my desired min-max connection parameters are the same as during the initial connection. I find...
I have an imuduino (arduino board with nrf8001 bluetooth and some sensors) board and am trying to load some of the profiles from the nordic arduino nrf8001 bluetooth api on...
Hello
I made the switch from SDK 6.0.0 to SDK 6.1.0 with SD7. At first we didn't get it to work. We would get the error NRF_ERROR_INVALID_PARAM on dm_init(). The problem...
Hello, I set up the environment by This . Now I can ping the device on the raspberry pi.
How ever, When I run the python client example on My ubuntu-14.04 and try to connect...
Hi, where can I get access to the definition and meaning and definition of the built in functions and headers of nrf51822? for instance what does this mean: uint8_t err_code...
Hi ,
I am using nRF6.0.0, SoftDevice 7.0, for nRF 6310 hardware.
I am trying to develop a ble keyboard app with the help of Ble Keyboard Sample we have in the SDK. As...
HI,
I am currently working on a project to develop firmware for S110 nRF51822 softdevice .
Currently I have a device with the following details: Ic Version - 2, Variant...
Hello, I am trying to make adc sampling on two adc inputs at the same time. The adc example (simulataneous-adc-sampling-from-two-inputs) is not using IRQ handler and applying...
Can i flash the stack S310 in any nRF51822?
I have a NRF51822 QFAAG0 but I cant run the example ble_ant_app_hrm properly.
I use Keil MDK5 and nRF51 SDK 5.1.
Thanks...
Which works better:
a single GATT characteristic using 'write without response' for transmission from the central to the nRF51822/S110 peripheral and 'notifications...
Hello everybody,
I searched the forums and saw numerous questions regarding sampling multiple ADCs but none for this exact use case.
The question is simple - is it possible...
Setup: Galaxy S3 (Android 5.1.1), nRF52 with S132
Basically I am trying to estimate distance from the phone on the nRF52 by measuring the RSSI and in order to do this to...
