Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Segger embedded studio V4.18 appears to have a bug when it comes to printing to RTT. When I run the exact same firmware on SES V3.40, everything is printed to the debug window...
Whether I could build BLE_MESH network automatically within some BLE devices without provisioner?e.t I feel it is manual to build BLE_MESH network with the help of provis...
Hello,
for my project, I am using the module BT832A (from Fanstel) that implements the nrf52810. I am using the pin P.021 to drive a switch. The problem is that when I set...
Hello. I have a problem getting a position via GPS. My dev board is placed in a good place, but can't get a position after more than 1 hour.
I am using you new SW version...
I have been using using nRF9160 as ble gateway for uploading data from one nRF52832 and its works well. Now I need to connect more than one nRF52832 devices, has anyone tried...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello all,
I am attempting to develop an application which utilizes a third party library for proprietary sensor calculations. This library requires the use of floating...
Hi DevZone team,
Hope you're doing great today. Just want to confirm if the nRF9160 is ready to operate in Mexico. The LTE Bands needed are B2, B4, B5 and B28. The IFETEL...
Hi,
I use SDK 10 pwm example (examples\peripheral\pwm) to modify the PWM cycle to 10s and duty cycle to 50%.
Code showed as below:
But the PWM cycle seem only around...
I have seen the datasheet of nRF52840 but I can't find that any GPIO pin used as SPIS. It says that you can configure the pin those whose value is written in the PSEL.MOSI...
Hello everyone!
I've tried to run mbedtls crypto functions which are using cc310 hardware implementation and I have partitions overlap issue.
Our main goal is to test...
Hi there, I've been testing out handling the Apple Notification Service notifications.
I have set up the handler for the ancs_object as on_ancs_c_evt, I can successfully...
Hi,
I'm currently doing a project where I want to sample an SAADC and send it over Bluetooth to another nRF52840 device with different sampling frequencies. The problem...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi All,
I am new to nordic, i am using nrf52840 development kit and using the SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
I would like to start the program from...
