Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I would like to know if there is any reason that tx_power is limited to +4dBm in the Mesh examples. I am using an nrf52840 and it is capable of +8dBm. Would it increase...
I am starting afresh, and have only just downloaded & installed Keil v5.25, nRF SDK v15.0.0, and nRFgo Studio v1.21.2.10
So everything should be "latest" and "up-to-date...
I am working on small UART project. I am begineer coder.
I want to transmit 0-9 numbers using UART. I am using nRF52832 board and IDE using is Eclipse pca10040. I applied...
Hi,
I am using nRF52832 pca10040 developement board. As I am begineer I dont know much about coding. I am using Eclipse IDE for developement. I want to transmit 1-10 numbers...
Did somebody ever get the following error message:
/usr/lib/gcc/arm-none-eabi/7.1.0/../../../../arm-none-eabi/bin/ld: unrecognised emulation mode: cpu=cortex-m4 Supported...
Good morning everyone,
I am having a few problems in understanding the new SDK 15.0.0.
First of all, I was unable to find a definition/description of NRFX.....what is...
Hi!
I have some doubt's on Light Switch example in SDK for Mesh V.2.0.0
1. I'm able to connect using nRF Connect Android Application to Proxy Client and Server but when...
Hi,
I'm using the nRF51 Dongle as a sniffer to capture BLE data. I set up the device and the plugin as instructed in the User Guide 2.0.
1. When starting Wireshark, the...
Hello,
I am using sdk 12.2.2 and customised nrf52 board. I am using gcc makefile to compile my code. I want to add .lib file in my code so how should I add .lib file in...
Hi,
I want to send "ON" message to server node over mesh network when a client node receives "hello" via UART from PC
I was able to merge UART example from nrf5 sdk with...
We are using BMD300 module in our custom design, but we are facing issue in programming BMD300 using j-link segger. The device is not getting detected in nRFgo studio. But...
Hi
We are having our current NRF application working with S132 SoftDevice v3.0.0 API and we want to port our application on S132 SoftDevice v5.0.0 API and also want to use...
Hi,
Im not sure if im doing something wrong or what, but i've been hitting a wall when trying to use the radio example transmitter and receiver.
No matter what i send...
