Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi there,
First: I’m a newby, just did some things with Arduino to control some LEDs etc but not much more before.
What’s my plan: I actually ‘ld lik to control some...
I am new to BLE development and have started by installing SEGGER Embedded Studio
Release 3.30 and have a J-LINK edu usb device and a Core51822 board from Wavetek.
I understand...
I am using various sensors to build a wireless sensor network. There are libraries for sensors that are provided by developers such as from adafruit or sparkfun. I have been...
What is the easiest way to use Arduino libraries into nrf52 projects in Keil on C?
Arduino has a lot minus : bad ide, not support debug mode, not optimize code size. But...
I work with nRF52832, based on SDK 14.0.0, and I have done DFU operation successfully with nRF connect on iOS, but when I used Android phone, nRF connect couldn't start DFU...
ble_app_gls_pca10056_s140.hex
Hi,
I am new in this field and i am trying to do current measurement on the nrf52840 PDK using PPK, in sleep mode(sd_power_system_off) i...
Hi,
I have just bought an nRFGo Motherboard (nRF6310) to develop for the nRF24LE1 (nRF2722). I was able to run some example code on the chip like toggling a pin. Next I...
Hello,
I have an application based on SDK 11 and Softdevice v2.0.0. Also there is a legacy bootloader from SDK 11 for performing DFU.
I am wondering whether it is possible...
When I run the UART app nRF5_SDK_12.3.0_d7731ad\examples\peripheral\uart in debug mode, the disassembly window opens, and I seem to get stuck on the second instruction. Step...
I am using a nRF52 and I have to measure two voltages:
the first continuously
when a command is received, the second voltage have to be measured and then...
Hi,
I flashed my nRF52840-PDK with UART/Serial Port Emulation over BLE program. Everything seems to be ok and I can connect with board via Android application. Next I would...
Hi!
I try to send data using advertise PDU and I need use custom 128 UUID.
How to convert to right format service_128_uuid and replace 16-bit value to init.advdata.p_service_data_array...
I'd like to use the nrf52832 as a mesh switch with battery powered. But I didn't find any sample code for the Low power feature in current mesh SDK v0.10.1. Does it support...
